Detroit 60 series starting problems.

Jump to page : 1. Now viewing page 1 [50 messages per page] Subject: At wits end....Detroit Series 60,need ideas! DDEC 3,1994 430/470 hp. Getting a flutter in motor at speeds higher than bottom of box,will not do it bob-tail but with a load will do it. Things checked so far are. Fuel pressure,getting 20psi at idle and 70psi at higher revs. Fuel ...Series 60 Synchronous Reference Sensor. The Synchronous Reference Sensor (SRS) is an electronic component that is mounted to the rear of the gear case. The sensor portion of the SRS extends through a hole in the gear case, and is positioned very near the rear of the bull gear. A bolt, inserted through a hole in the SRS bracket, secures …1. Remove the valve rocker cover (s); 2. Remove the wire mesh form the rocker cover; 3. Install a new wire mesh element to the rocker cover; 4. Install the rocker cover to the engine; 5.Series 60 - Low Power Troubleshooting Chart. There are three basic checks that should be performed: Check for active/historic codes. All causes need to be checked once the fault is identified. Record faults on the Application For Adjustment (AFA) claim, if there is to be a claim. Check the DDEC parameters, progressive shift settings, torque ...Acton, CA. Occupation. Owner/Operator grading business. Jun 28, 2009. #1. The truck is a 98 Western Star with a 12.7 liter series 60 Detroit engine (500hp). The problem is that it is loosing prime when sitting overnight and is hard to start. A description of the fuel system is as follows. The fuel tube out of the tank goes under the cab to a ...

When checking fuel pressure, start the engine, run at the speeds listed in Table 12-3, and record fuel pressure. Shut down the engine. 4. Shut down the engine. 5. Remove the calibrated gauge from the fuel pump. 6. Reinstall the SFT Sensor, refer to the Series 60 Service manual (6SE2007), fuel system.Series 60 – STARTING DIFFICULTY – ENGINE ROTATES – CRANK NO START. The engine cranks but does not start. Check for the following: Low Fuel Level. …1. 1. 1. 1. ATTENTION. The information in this document is accurate as of April 2004 and is subject to change without notice. This manual is to be used in conjunction with the DDEC III/IV Single ECM Troubleshooting Guide and the DDEC V Single ECM Troubleshooting Guide. Series 60®, Detroit Diesel®, DDC®, DDEC® and the spinning arrows design ...

Fuel Injection System: The Detroit 60 Series is equipped with a high-pressure common rail fuel injection system. This system consists of fuel injectors, a common fuel rail, a fuel pump, and an electronic control module (ECM). The ECM controls the fuel delivery based on inputs from various sensors, such as throttle position, engine speed, and ...Batteries are the usual problem in this case. Even if your voltmeter says things are ok when your cranking your starter is spiking your truck voltage down and your DDEC is shutting off or at best not able to provide enough voltage to fire the injectors. As soon as you release the starter voltage comes back up and turns the DDEC back on.

Detroit Series 60 won't start, there is fuel pressure, changed both sensors, Starts with fluid, but dies as soon as fluid spray stop 1999 International ... I took a 60 series Detroit out of 2003 Freightliner Columbia and put it in 1999 Freightliner FLD. It will crank along as I'm spraying ether .But goes dead when I stop spraying. Took it to ...If the basic mechanical checks fail to locate the problem, refer the Detroit Diesel Single ECM Troubleshooting Manual, (6SE497). Start by reading the "Basic Knowledge Required" section before attempting to diagnosis electrical faults.‪ ... Series 60 – Section 2.47 Impco Low Pressure Fuel Regulator for the Series 60G Engine High …I have a 97 FLD 120 with a series 60 engine. As soon as I start the truck the fan comes on and stays on, cant seem to figure out what might be causing it. just replaced the bearing in the fan clutch. i check for an air leak. please help....Series 60 DDEC V Troubleshooting – Section 77.2 Troubleshooting Flash Code 87, PID 73/FMI 4; Series 60 DDEC V Troubleshooting – Section 78 Flash Code 89 – AECL Sensor Fault or Fuel Inlet Restriction High; Series 60 DDEC V Troubleshooting – Section 78.1 Description of Flash Code 89, PID 111/FMI 12 & PID 95/FMI 0Problem solved. Happy trucker. Well i hope this helps even just one person. If it does it was worth it. If any one has any input for me that i may need correcting please email me. ALways like to hear of better ways. ... 60 series Detroit Diesel won't start - tommyw-5088: 1/24/2010 18:57. Re: 60 series Detroit Diesel won't start - milofarmer1: 1 ...

Series 60 – STARTING DIFFICULTY – ENGINE ROTATES – PLUGGED FUEL FILTER(S) To determine if a plugged fuel filters is causing starting difficulty, perform the following steps: 1. Disconnect the fuel line…

Section 4Symptom Based Diagnostics – Hard Starting. A hard start or no start condition can be caused by many different conditions. Some of these conditions can be related to the fuel system.‪. 4.1 Engine Will Only Start Using An External Priming Source. 4.2 Fuel System Checks for No or Hard Starting. DD15 Fuel System Technician's Guide ...

Gage reading = (lb/in. 2) x 27.7 = inches of water‪ Gage reading = (lb/in. 2) x 2.04 = inches of mercury‪ Section 12.7.3.2 Run-in Procedure. Use the following procedure for preparation of engine run-in. See Figure "Series 60 Engine Test Report Form", part A.‪ Fill the lubrication system as outlined under Lubrication System , "Preparation for a First …Series 60 - Section 1.28 Camshaft and Camshaft Bearing; Series 60 - Section 1.27 Thrust Plate Perimeter Seal; Series 60 - Section 1.24 Gear Train and Engine Timing; Series 60 - Section 1.25 Compact Gear Train and Engine Timing; Series 60 - Section 1.26 Camshaft Gear Assembly Series 60 Exhaust Gas Recirculation (EGR) ModelI have a 60 series Detroit seems to start fine then shortly runs out of fuel dies sometimes I can crank it over and it - Answered by a verified Technician. ... Hey I have 1990 379 Pete with Detroit 60 series 12.7…my problem before was truck cranking and shutting of after maybe 30sec-2-3min.13. Jun 14, 2011. San Angelo, TX. 0. Don't know as I have only had mine a couple of weeks, but sometimes after sitting maybe 2 days, mine does not want to start. It will finally fire up after cranking on it hard and it chugging like an old tin lizzie for a minute. BigfootWRL, Jun 14, 2011. #2. Jun 15, 2011 #3.5 Apr 2023 ... Dakota shows how to check the ECM or computer of a Detroit series 60 engine and some bonus footage of how to properly take off a driveshaft ...

Section 1.16Flywheel. The flywheel is attached to the rear end of the crankshaft with twelve bolts. The bolt holes in the crankshaft and flywheel are equally spaced. The flywheel is not indexed to the crankshaft, and may be installed in any position. A scuff plate is used between the flywheel and the bolt heads to prevent the bolt heads from ...A dual spin-on lube oil filter adaptor assembly with a temperature-sensitive thermatic oil control valve is available on Series 60,… Series 60 Valve Guide Parts Valves are positioned and aligned by replaceable valve guides pressed into the cylinder head.The #2 factor in getting better fuel mileage is to AVOID RUNNING THE ENGINE WHEN YOU ARE NOT MOVING. The #3 factor in getting better fuel mileage is the engine. Everyone wants to look at the engine first , because they think the part that burns the fuel is the most responsible for fuel economy.To determine if aerated fuel is causing starting difficulty, perform the following steps: ‪. Disconnect the fuel line return hose from the fitting located at the fuel tank; refer to OEM guidelines. Place the opened end of the fuel line into a suitable container. Start the engine. Run the engine at 1000 r/min.First things first get a DDEC 4 box program it to the original serial number of the engine you put in the 99. The engine serial number is below intake manifold on left side of block usually 06r0xxxxxx. I know all 60s look the same but they are not. It should run better now because the ecm is matched to the engine.Yes, it can be difficult to cold start Detroit diesel series 60. One way to solve this issue is to regularly change the SRS and TRS sensors. However, keep in mind that both sensors should be replaced at the same time. It is also recommended to periodically maintain the cooling system to solve this issue.Hi I have 2006 freightliner Detroit 60 series 14l with egr losing power and white smoke when engine reaches normal temperature the shop has already replaced 3 pods 2 turbos ,egr,ecm,engine harness,vpod harness the problem has still not been found after all these parts I still get load of white smoke when engine reaches normal temperature.

201. 95. Feb 13, 2009. California. 0. Just purchased 2000 Fld120, with detroit 60. After driving it for about 30 minutes, noticed the engine surges, up to 1500 rpm's when idled (intermittently). Once its in gear, it will lower rpms, enough to start off, but then intermittently throughout the gears the engine will begin to surge again.I have a Freightliner Century with a Detroit 12.7 s60. Recently the truck has become very hard to start and has lost power specially when going up hills. I have checked and cleaned the check valve on the filter and also the check valve behind the cylinder head. But still the same difficulty in starting, I have to use starting fluid all the time.

Detroit Series 60 Problem. My 06 Detroit Series 60 started doing something really strange this week. First day it started acting up: When I start it up in the morning after it has been sitting all night it starts up fine and idles at 800rpm. When it starts to warm up the rpm drops to 600rpm like normal and then it starts puffing black smoke ...Problem starting 12.7 Detroit Jump to page : 1 Now viewing page 1 [50 messages per page] View previous thread:: View next thread Forums List-> Machinery Talk: ... I have a 60 series that had starting issues last harvest. It would start with ether but it was either the crank sensor or cam sensor. Replaced them both and now it starts:Information for Series 60 Engines,” available from authorized Detroit Diesel service outlets. Keep this Operator's Guide with the engine installation at all times. It contains important operating, maintenance, and safety instructions. Trademark Information DDC®, Detroit Diesel®, DDEC®, Series 60®, Optimized Idle®, Diagnostic Link ...Carefully fasten connector onto sensor and engage locking tang. Turn the ignition to the ON position. Observe the DDR for any diagnostic code (s). If any code (s) other than code 25 is logged, refer to the Detroit Diesel Single ECM Troubleshooting Manual (6SE497). Series 60 Service Manual - 6SE483.Have 60 series detriot with a starting problem, it loses prime have replaced lines shut offs, and check valve on return - Answered by a verified Technician ... 1998 Freightliner series 60 Detroit multiple fuel related problems after sitting for periods of time when engine is first started sounds like it's running on one cylinder very very rough ...Series 60 12.7 year 2003 i checked harness pins for volts and the big pin close to cab has 4 pins with 12 volts and a 5 large pin cable above it has two pins with 12 volts. So ecm is getting power but dash is not reading anything from it shows 0 volts no eng with alot of faults and also check eng and protect is constantly on once you turn the key.I have a detroit 60 series 12.7. It is in an 2003 Freightliner XL classic. ... Replace it and rule it out as being the problem. ralph, Jan 15, 2013. ralph, Jan 15 ... Feb 21, 2010 Rock Creek B.C. Canada 0. A 60 series needs 195 RPM to start and it needs an SRS signal. when you try starting it, look, with a flashlight into the fuel tank, you ...

20 Oct 2013 ... How to test your starter motor & solenoid - Starter troubleshooting ... 60 series Detroit injector problem. Arsen ... Detroit Series 60 starter ...

Jun 15, 2010 · Make sure the filters are full. Crack the small line on the transfer pump and spin it over. Maybe a SMALL shot of ether and see if fuel comes out. Pump is on the back of the compressor. Big in, small out. 2005 250 Super Duty Crew. White and Grey. ARP studs, EGR Delete, and SCT from Vivian. CCV re-route, and 4" Magnaflow turbo back.

View the ECM/ECU output functions and set them to particular values to support troubleshooting. This can be particularly useful when troubleshooting electrical problems. View engine and trip totals. View the status of a set of maintenance monitors. Section 19.5.1.3 Snapshots. To start a new snapshot, perform the following steps.‪Unhooked the jake connector near starter and towed a motor home, about 4 hours work, no problems. However the tach gets jumpier/more erratic as the truck runs longer. Set chk engine light immediately upon start-up w/jakes unhooked. Cruise & fast idle still worked,,, when the problem starts the cruise/idle up quit.Disassemble the rocker cover as follows:‪. Disengage the clip that holds the crankcase vent breather element in the valve cover by pressing the center of the spring steel retaining clip outward and removing the straight end. Rotate the clip upward to remove the curved end. Remove the wire mesh element. Section 1.6.7.Section 4Symptom Based Diagnostics – Hard Starting. A hard start or no start condition can be caused by many different conditions. Some of these conditions can be related to the fuel system.‪. 4.1 Engine Will Only Start Using An External Priming Source. 4.2 Fuel System Checks for No or Hard Starting. DD15 Fuel System Technician's Guide ...Great place to get rebuild parts for cheap! To answer your question: you are paying way to much for a Detroit Diesel Label...the in-frame kit for an 11.1L or 12.7L series 60 is $2,200 for an engine with an oldstyle piston and $2,500 for an engine with a new style piston.I swapped out a Detroit series 60 14.0L and put in an older Detroit series 60 12.7 L into my 2006 Columbia freightliner modified all the harness, the only problem is that my throttle does the opposite … read moreThe Detroit Diesel Series 40 Troubleshooting Guide is a comprehensive resource specifically designed to provide detailed information on efficiently diagnosing and resolving issues with the Series 40 engine. This guide serves as an invaluable reference for technicians and mechanics, offering essential guidance on effectively troubleshooting and ...Batteries are the usual problem in this case. Even if your voltmeter says things are ok when your cranking your starter is spiking your truck voltage down and your DDEC is shutting off or at best not able to provide enough voltage to fire the injectors. As soon as you release the starter voltage comes back up and turns the DDEC back on.1. Connect Detroit Diesel Diagnostic Link (DDDL 7.0) to check the oil pressure. 2. Start and vary engine speed between 1800 - 2100 rpm. 3. Check DDDL 7.0 for oil pressure reading. [a] If DDDL 7.0 indicates oil pressure greater than or equal 241 kPa (35 psi) at 1800 rpm, shut down the engine and disconnect DDDL 7.0. Refer to section 6 to diagnose

1. Effective with 6R56762, a manually operated fuel shutoff valve replaced a check valve. A PRO-CHEK ® valve may be installed at this location to remove air. ‪. 2. Effective with 6R8950, the ECM/EDU cooler unit was removed from all Series 60 engines used in on-highway applications. ‪. 3. Effective with unit 6R13060, a fuel system check ...Have a 60 series detroit in a 05 western star that keeps going through ecms. Original one went. Dealer installed new one - Answered by a verified Technician ... They installed another ecm that now has 315 hrs on it and problems are starting again. No start yesterday morning left truck for a couple hrs. Flashed codes got 86 and 21 pulled ecm ...Posted 1/12/2012 17:05 (#2158046 - in reply to #2156817) Subject: Re: ?'s about 60 series detroit made in about 1996. NC ND. '96 should be a DDECIII, would be skeptical of the 475, I've only known them to be 430-470 or 485. Blow-by is one of the better ways to know what shape the engine is in.Instagram:https://instagram. ley lines tennesseebotw beedle restockmayra and donnie still togetheru s navy rank crossword 1994 Detroit 60 Series 12.7 jake brake problem. Discussion in 'Freightliner Forum' started by davis28905, Sep 15, 2021. Sep 15, 2021 #1. davis28905 Bobtail Member. 2 0. Sep 15, 2021 0. My 4cyl jakes act like they don't turn off when you hit the accelerator, clutch or even turn the switch off. They sound like they keep running for a few seconds ...There are three basic checks that should be performed: Check for active/historic codes. All causes need to be checked once the fault is identified. Record … lyndhurst public schools employmentfood disposal reviews 3. Disconnect ventilation pipe from valve cover. 4. Remove engine cover. 5. Adjust Jake Brake (if applicable), injectors and valves following instructions in the Detroit Diesel service manual for series 60 engines. 6. Verify engine cover gasket and replace if necessary.The Series 60 diesel engine Fuel Temperature Sensor (FTS) is installed into the secondary fuel filter. ... Observe the DDR for any diagnostic code(s). If any code(s) other than code 25 is logged, refer to the Detroit Diesel Single ECM Troubleshooting Manual (6SE497). Series 60 Service Manual - 6SE483: Generated on 10-13-2008: Posted in Fuel ... copc westerville patient portal Detroit series 60 12.7 fuel issues. I have been having a heck of a time trying to source my issue with air in my fuel system. It all started after truck would sit a few days. It would be hard to start then be good once running but then became problematic and needed the fuel tank pressurized to start and it would still get air after running a ...Series 60 white smoke at startup. ... Feb 8, 2018 #1. tnpete Medium Load Member. 561 608. Jun 25, 2013 Tn 0. My Detroit has been one of those with the white smoke at startup. Well today I did something different. And only one small puff of smoke at startup. ... I felt the same with my big cam 400 cold start.year round. Got rid of the skeeters ...Detroit 60 series 12.7L Egr problems ... ddec 5 is down I can no longer pull loads with it and not one shop can give me a answer on the dyno today the the truck starts making 32lbs of boost than turbo will cheerp and boost drops down to 20lbs than while doing that it rolls black smoke than Egr temp was over 600 degrees the fan comes …